quinta-feira, 12 de junho de 2014

Charging portable electronics in 10 minutes: New architecture for lithium-ion battery anodes far outperform the current standard

 


Mihri and Cengiz Ozkan, both professors in the Bourns College of Engineering.

Researchers have developed a three-dimensional, silicon-decorated, cone-shaped carbon-nanotube cluster architecture for lithium ion battery anodes that could enable charging of portable electronics in 10 minutes, instead of hours.

Lithium ion batteries are the rechargeable battery of choice for portable electronic devices and electric vehicles. But, they present problems. Batteries in electric vehicles are responsible for a significant portion of the vehicle mass. And the size of batteries in portable electronics limits the trend of down-sizing.

Silicon is a type of anode material that is receiving a lot of attention because its total charge capacity is 10 times higher than commercial graphite based lithium ion battery anodes. Consider a packaged battery full-cell. Replacing the commonly used graphite anode with silicon anodes will potentially result in a 63 percent increase of total cell capacity and a battery that is 40 percent lighter and smaller.

In a paper, Silicon Decorated Cone Shaped Carbon Nanotube Clusters for Lithium Ion Battery Anode,recently published in the journal SMALL, UC Riverside researchers developed a novel structure of three-dimensional silicon decorated cone-shaped carbon nanotube clusters architecture via chemical vapor deposition and inductively coupled plasma treatment.

Lithium ion batteries based on this novel architecture demonstrate a high reversible capacity and excellent cycling stability. The architecture demonstrates excellent electrochemical stability and irreversibility even at high charge and discharge rates, nearly 16 times faster than conventionally used graphite based anodes.

The researchers believe the ultrafast rate of charge and discharge can be attributed to two reasons, said Wei Wang, lead author of the paper.

One, the seamless connection between graphene covered copper foil and carbon nanotubes enhances the active material-current collector contact integrity which facilitates charge and thermal transfer in the electrode system.

Two, the cone-shaped architecture offers small interpenetrating channels for faster electrolyte access into the electrode which may enhance the rate performance.

Wang is a graduate student advised by Cengiz S. Ozkan, a mechanical engineering professor at UC Riverside's Bourns College of Engineering; and Mihrimah Ozkan, an electrical engineering professor. Both of them are co-authors of the paper.

Other co-authors are Isaac Ruiz, Kazi Ahmed, Hamed Bay, Aaron George, who are all graduate students, and Johnny Wang, an undergraduate student.

A fuel cell for home: Tested in private households

 


Production of the cell stacks at the Fraunhofer IKTS.

It converts chemical energy directly into electrical energy. Still, there hadn't been a market breakthrough for the fuel cell. The systems were too complex. Now, Fraunhofer and Vaillant have developed a simple device for home use.

"One always speaks of a fuel cell system," says Dr. Matthias Jahn from the Fraunhofer Institute for Ceramic Technologies and Systems IKTS in Dresden. A single cell doesn't produce enough voltage to obtain a sufficient electrical power. In a fuel cell stack, several cells are connected one to the other. Each of them is about the size of a CD. We call the groups ‚stacks'," says Jahn. Fuel cells convert natural gas directly into electrical energy. They are many times more efficient than are combustion engines, such as the car engine. These require an intermediate step. First, they convert chemical energy into thermal energy (heat) and mechanical energy (force). With this force, they drive a generator, which only then generates the electric power. In the process, a large portion of the originally available energy is lost.

Real-life test in private households

Together with the heater manufacturer Vaillant, the IKTS has developed a compact, safe and sturdy fuel cell system that generates electricity and heat in private households from natural gas. The researchers were particularly responsible for the construction of the prototype, the design of the overall system, the design of the ceramic components and the development of the reformer and the afterburner. The devices are currently being tested in private households in the Callux practice test.

They are as compact as classical gas heaters that only produce heat. Moreover, they can comfortably be mounted on the wall and easily be maintained. With an output of one kilowatt, they cover the average current consumption for a four-person household. The Federal Ministry of Transport and digital infrastructure BMVI is promoting Callux. Currently, in the European demonstration project ene.field, about 150 further units are being installed in several European countries. In addition, Vaillant started the production of a small-scale series in early 2014. Parallel to the practical test, the two partners are already working on new models. "Now, it's all about decreasing production costs and increasing the lifetime of the equipment," says Jahn.

The principle of the fuel cell has been known for over 175 years. So far, however, there has not been a market breakthrough. The main reason was the invention of the electric generator. It knocked the more complex fuel cell out of the running. Only in the 1960s was the technology put into practice by NASA in some Apollo moon missions. In the late 1990s, there were other projects in the automotive industry, which have so far not been able to prevail. The reasons are that the fuel cell is too complex, too expensive, and too unreliable. "In our project with Vaillant, we have made great strides to bring the technology close to the market. Vaillant is already producing a small-scale series, which is sold in funded projects to customers," says Jahn. "For the market breakthrough, the costs still have to be decreased significantly."

The miniature power station for home use is based on a solid fuel cell (SOFC). SOFCs operate at a much higher temperature in comparison to competing approaches, such as the proton exchange membrane fuel cell (PEMFC), which is used in cars, for example. While PEMFCs only reach 80 degrees, SOFCs can reach up to 850 degrees. "This allows the SOFCs to be built much more simply and cheaply," says Jahn.

The electrolyte of an SOFC only transfers oxygen ions, not electrons. Otherwise, there would be a short circuit. "Ceramic is particularly well suited as a material for the electrolyte. It has the desired conductivity and can also endure high temperatures," says Jahn. As a result, even without the use of precious metals, all reactions proceed smoothly, which is necessary for the direct conversion of chemical energy into electrical energy: If the fuel cell heater is connected to the gas network, a reformer initially converts the natural gas into a hydrogen-rich gas. This then reacts in the stack with the oxygen of the air in a noiseless "cold combustion," producing power and heat.


Story Source:

The above story is based on materials provided by Fraunhofer-Gesellschaft. Note: Materials may be edited for content and length.

Chemical sensor on a chip created to test chemical composition of liquids

 


Just a drop is enough to test the chemical composition.

Using miniaturized laser technology, a tiny sensor has been built at the Vienna University of Technology which can test the chemical composition of liquids.

They are invisible, but perfectly suited for analyzing liquids and gases; infrared laser beams are absorbed differently by different molecules. This effect can for instance be used to measure the oxygen concentration in blood. At the Vienna University of Technology, this technique has now been miniaturized and implemented in the prototype for a new kind of sensor.

Specially designed quantum cascade lasers and light detectors are created by the same production process. The gap between laser and detector is only 50 micrometres. It is bridged by a plasmonic waveguide made of gold and silicon nitride. This new approach allows for the simple and cheap production of tiny sensors for many different applications.

Laser and Detector Simple solid-state lasers, such as the well-known red ruby laser, consist of only one material. Quantum cascade lasers, on the other hand, are made of a perfectly optimized layer system of different materials. That way, the properties such as the wavelength of the laser can be tuned. When a voltage is applied to the layer structure, the laser starts to emit light. But the structure can also work the other way around; when it is irradiated with light, an electric signal is created.

Now a method has been developed to create a laser and a detector at the same time, on one single chip, in such a way that the wavelength of the laser perfectly matches the wavelength to which the detector is sensitive. This bifunctional material was created atomic layer for atomic layer at the center for micro- and nanostructures at the Vienna University of Technology. "As both parts are created in one step, laser and detector do not have to be adjusted. They are already perfectly aligned," says Benedikt Schwarz.

Leading the Light to the Detector

In conventional systems, the laser light has to be transmitted to the detector using carefully placed lenses. Alternatively, optical fibres can be used, but they usually transport all the light inside, without letting it interact with the environment, and therefore they cannot be used as sensors.

In the new element created at the Vienna University of Technology, the optical connection between quantum cascade laser and detector works in a completely different way. It is a plasmonic waveguide, made of gold and silicon oxide. "The light interacts with the electrons in the metal in a very special way, so that the light is guided outside the gold surface," says Benedikt Schwarz. "That is why the light can be absorbed by the molecules on its way between laser and detector."

The sensor chip can be submerged in a liquid. By measuring the decrease of the detected light intensity due to the presence of light absorbing molecules, the composition of the liquid can be determined. The sensor was tested with a mixture of water and alcohol. The water concentration can be measured with an accuracy of 0.06%.

As the wavelength can be influenced by changing the design of the layered structure, this sensor concept can be applied to a wide variety of molecules such as carbohydrates or proteins, for many different applications in chemical, biological or medical analytics.


Story Source:

The above story is based on materials provided by Vienna University of Technology. The original article was written by Florian Aigner. Note: Materials may be edited for content and length.


Humans climb like geckos using bio-inspired climbing technology

 

June 11, 2014

DARPA's Z-Man program has demonstrated the first known human climbing of a glass wall using climbing devices inspired by geckos. The historic ascent involved a 218-pound climber ascending and descending 25 feet of glass, while also carrying an additional 50-pound load in one trial, with no climbing equipment other than a pair of hand-held, gecko-inspired paddles. A novel polymer microstructure technology was used in those paddles.


During testing, an operator climbed 25 feet vertically on a glass surface using no climbing equipment other than a pair of hand-held, gecko-inspired paddles. The climber wore, but did not require, the use of a safety belay.

DARPA's Z-Man program has demonstrated the first known human climbing of a glass wall using climbing devices inspired by geckos. The historic ascent involved a 218-pound climber ascending and descending 25 feet of glass, while also carrying an additional 50-pound load in one trial, with no climbing equipment other than a pair of hand-held, gecko-inspired paddles. A novel polymer microstructure technology was used in those paddles.

Historically, gaining the high ground has always been an operational advantage for warfighters, but the climbing instruments on which they're frequently forced to rely -- tools such as ropes and ladders -- have not advanced significantly for millennia. Not only can the use of such tools be overt and labor intensive, they also only allow for sequential climbing whereby the first climber often takes on the highest risk.

DARPA created the Z-Man program to overcome these limitations and deliver maximum safety and flexibility for maneuver and rapid response to warfighters operating in tight urban environments. The goal of the program is to develop biologically inspired climbing aids to enable warfighters carrying a full combat load to scale vertical walls constructed from typical building materials

Geckos can climb on a wide variety of surfaces, including smooth surfaces like glass, with adhesive pressures of 15-30 pounds per square inch for each limb, meaning that a gecko can hang its entire body by one toe. The anatomy of a gecko toe consists of a microscopic hierarchical structure composed of stalk-like setae (100 microns in length, 2 microns in radius). From individual setae, a bundle of hundreds of terminal tips called spatulae (approximately 200 nanometers in diameter at their widest) branch out and contact the climbing surface.

A gecko is able to climb on glass by using physical bond interactions -- specifically van der Waals intermolecular forces -- between the spatulae and a surface to adhere reversibly, resulting in easy attachment and removal of the gecko's toes from the surface. The van der Waals mechanism implied that it is the size and shape of the spatulae tips that affect adhesive performance, not specific surface chemistry. This suggested that there were design principles and physical models derived from nature that might enable scientists to fabricate an adhesive inspired by gecko toes.

Humans, of course, have much more weight to carry than a gecko. One of the initial challenges in developing a device to support human climbing was the issue of scaling: a typical Tokay gecko weighs 200 grams, while an average human male weighs 75 kilograms. To enable dynamic climbing like a gecko at this larger scale required that the engineers create climbing paddles capable of balancing sufficient adhesive forces in both the shear (parallel to the vertical surface) and normal (perpendicular to the vertical surface) directions. That feature is necessary for a climber to remain adhered on a surface without falling off while in the act of attaching and detaching the paddles with each movement.

The Draper Laboratory team was also challenged to create novel micro- and nanofabrication technologies to produce the high-aspect-ratio microstructures found in the gecko toe. In the process of achieving that capability, the Z-Man performers transformed the fundamental design and development of reversible adhesives for potential biomedical, industrial, and consumer applications.

The first human climbing demonstration occurred in February 2012 and tests of the technology are ongoing.


Story Source:

The above story is based on materials provided by DARPA. Note: Materials may be edited for content and length.

Dangerous, underpaid work for the undocumented

 

June 10, 2014

Cornell University

Illegal immigrants don't hold the most dangerous jobs in the United States. That kind of work pays a decent wage for the risk to life and limb, and undocumented workers are barred from those jobs. Yet there is plenty of hazard, risk and occupational injury for the uncounted millions of illegal immigrants doing the 'merely dangerous' work no one else wants -- without a pay premium from employers who take advantage of that labor pool, a study reveals.


Yet there is plenty of hazard, risk and occupational injury for the uncounted millions of illegal immigrants doing the "merely dangerous" work no one else wants -- without a pay premium from employers who take advantage of that labor pool, a Cornell-Penn State University study reveals.

"Undocumented Mexicans receive effectively no wage premium for working in dangerous settings, whereas most other groups (including legal Mexican immigrants, and native whites, blacks and Hispanics) do," says Matthew Hall, assistant professor of policy analysis and management in Cornell's College of Human Ecology.

With Penn State's Emily Greenman, Hall published "The Occupational Cost of Being Illegal in the United States: Legal Status, Job Hazards and Compensating Differentials" this month online in the journal International Migration Review.

They report: "Undocumented workers are rewarded less for employment in hazardous settings, receiving low or no compensating differential for working in jobs with high fatality, toxic materials or exposure to heights ... legal status plays an important role in determining exposure to job hazard and in structuring the wage returns to risky work."

The researchers' study focused on undocumented immigrants from Mexico and Central American countries and noted that the majority of Hispanic undocumented workers in the United States today are Mexican.

The social scientists discount popular claims that undocumented workers are engaged in the very most dangerous occupations -- logging or mining, to name jobs with the most fatalities according to the Bureau of Labor Statistics. Regulatory oversight of extremely hazardous workplaces keeps undocumented workers away from risky-but-remunerative jobs -- shuffling them to the margins, where danger also lurks. Agricultural workers can be maimed in farm equipment; day-labor construction workers fall from heights every day, they report.

Data analyzed by the social scientists come from the U.S. Census' Survey of Income and Program Participation, which includes information on citizenship and visa status; the Department of Labor's Occupational Information Network; and the Bureau of Labor Statistics' Census of Fatal Occupational Injuries.

Hall and Greenman highlighted language barriers to safety training, writing: "Employment in the construction industry, low likelihood of receiving safety training (due both to language barriers and reduced employer incentives to train temporary workers), employers flouting safety regulations with little fear of being reported by their undocumented employees, and severe economic pressures" force the undocumented to take less desirable jobs.


Story Source:

The above story is based on materials provided by Cornell University. The original article was written by H. Roger Segelken. Note: Materials may be edited for content and length.


Journal Reference:

  1. Matthew Hall, Emily Greenman. The Occupational Cost of Being Illegal in the United States: Legal Status, Job Hazards, and Compensating Differentials. International Migration Review, 2014; DOI: 10.1111/imre.12090

Mechanism explains complex brain wiring

 

June 11, 2014

VIB - Flanders Interuniversity Institute for Biotechnology

How neurons are created and integrate with each other is one of biology’s greatest riddles. Now, a researcher unravels a part of the mystery by describing a mechanism that explains novel aspects of how the wiring of highly branched neurons in the brain works. These new insights into how complex neural networks are formed are very important for understanding and treating neurological diseases.


Researcher Dietmar Schmucker from VIB-KU Leuven unravels a part of the mystery in Science magazine. He describes a mechanism that explains novel aspects of how the wiring of highly branched neurons in the brain works. These new insights into how complex neural networks are formed are very important for understanding and treating neurological diseases.

Neurons, or nerve cells

It is estimated that a person has 100 billion neurons, or nerve cells. These neurons have thin, elongated, highly branched offshoots called dendrites and axons. They are the body's information and signal processors. The dendrites receive electrical impulses from the other neurons and conduct these to the cell body. The cell body then decides whether stimuli will or will not be transferred to other cells via the axon.

The brain's wiring is very complex. Although the molecular mechanisms that explain the linear connection between neurons have already been described numerous times, little is as yet known about how the branched wiring works in the brain.

The connections between nerve cells

Prior research by Dietmar Schmucker and his team lead to the identification of the Dscam1 protein in the fruit fly. The neuron can create many different protein variations, or isoforms, from this same protein. The specific set of isoforms that occurs on a neuron's cell surface determines the neuron's unique molecular identity and plays an important role in the establishment of accurate connections. In other words, it describes why certain neurons either come into contact with each other or reject each other.

Recent work by Haihuai H and Yoshiaki Kise from Dietmar's team indicates that different sets of Dscam1 isoforms occur inside one axon, between the newly formed offshoots amongst each other. If this was not the case, then only linear connections could come about between neurons. These results indicate for the first time the significance of why different sets of the same protein variations can occur in one neuron and it could explain mechanistically how this contributes to the complex wiring in our brain.

Clinical impact

Although this research was done with fruit flies, it also provides new insights that help explain the wiring and complex interactions of the human brain and shine a new light on neurological development disorders such as autism. Thorough knowledge of nerve cell creation and their neural interactions is considered essential knowledge for the future possibility of using stem cell therapy as standard treatment for certain nervous system disorders.


Story Source:

The above story is based on materials provided by VIB - Flanders Interuniversity Institute for Biotechnology. Note: Materials may be edited for content and length.


Journal Reference:

  1. H. He, Y. Kise, A. Izadifar, O. Urwyler, D. Ayaz, A. Parthasarthy, B. Yan, M.-L. Erfurth, D. Dascenco, D. Schmucker. Cell-intrinsic requirement of Dscam1 isoform diversity for axon collateral formation. Science, 2014; 344 (6188): 1182 DOI: 10.1126/science.1251852

Human language's deep origins appear to have come directly from birds, primates

 

Far from being a mere curiosity, the silvery gibbon may hold clues to the development of language in humans. In a newly published paper, two MIT professors assert that by re-examining contemporary human language, we can see indications of how human communication could have evolved from the systems underlying the older communication modes of birds and other primates.

From birds, the researchers say, we derived the melodic part of our language, and from other primates, the pragmatic, content-carrying parts of speech. Sometime within the last 100,000 years, those capacities fused into roughly the form of human language that we know today.

But how? Other animals, it appears, have finite sets of things they can express; human language is unique in allowing for an infinite set of new meanings. What allowed unbounded human language to evolve from bounded language systems?

"How did human language arise? It's far enough in the past that we can't just go back and figure it out directly," says linguist Shigeru Miyagawa, the Kochi-Manjiro Professor of Japanese Language and Culture at MIT. "The best we can do is come up with a theory that is broadly compatible with what we know about human language and other similar systems in nature."

Specifically, Miyagawa and his co-authors think that some apparently infinite qualities of modern human language, when reanalyzed, actually display the finite qualities of languages of other animals -- meaning that human communication is more similar to that of other animals than we generally realized.

"Yes, human language is unique, but if you take it apart in the right way, the two parts we identify are in fact of a finite state," Miyagawa says. "Those two components have antecedents in the animal world. According to our hypothesis, they came together uniquely in human language."

Introducing the 'integration hypothesis'

The current paper, "The Integration Hypothesis of Human Language Evolution and the Nature of Contemporary Languages," is published this week in Frontiers in Psychology. The authors are Miyagawa; Robert Berwick, a professor of computational linguistics and computer science and engineering in MIT's Laboratory for Information and Decision Systems; and Shiro Ojima and Kazuo Okanoya, scholars at the University of Tokyo.

The paper's conclusions build on past work by Miyagawa, which holds that human language consists of two distinct layers: the expressive layer, which relates to the mutable structure of sentences, and the lexical layer, where the core content of a sentence resides. That idea, in turn, is based on previous work by linguistics scholars including Noam Chomsky, Kenneth Hale, and Samuel Jay Keyser.

The expressive layer and lexical layer have antecedents, the researchers believe, in the languages of birds and other mammals, respectively. For instance, in another paper published last year, Miyagawa, Berwick, and Okanoya presented a broader case for the connection between the expressive layer of human language and birdsong, including similarities in melody and range of beat patterns.

Birds, however, have a limited number of melodies they can sing or recombine, and nonhuman primates have a limited number of sounds they make with particular meanings. That would seem to present a challenge to the idea that human language could have derived from those modes of communication, given the seemingly infinite expression possibilities of humans.

But the researchers think certain parts of human language actually reveal finite-state operations that may be linked to our ancestral past. Consider a linguistic phenomenon known as "discontiguous word formation," which involve sequences formed using the prefix "anti," such as "antimissile missile," or "anti-antimissile missile missile," and so on. Some linguists have argued that this kind of construction reveals the infinite nature of human language, since the term "antimissile" can continually be embedded in the middle of the phrase.

However, as the researchers state in the new paper, "This is not the correct analysis." The word "antimissile" is actually a modifier, meaning that as the phrase grows larger, "each successive expansion forms via strict adjacency." That means the construction consists of discrete units of language. In this case and others, Miyagawa says, humans use "finite-state" components to build out their communications.

The complexity of such language formations, Berwick observes, "doesn't occur in birdsong, and doesn't occur anywhere else, as far as we can tell, in the rest of the animal kingdom." Indeed, he adds, "As we find more evidence that other animals don't seem to posses this kind of system, it bolsters our case for saying these two elements were brought together in humans."

An inherent capacity

To be sure, the researchers acknowledge, their hypothesis is a work in progress. After all, Charles Darwin and others have explored the connection between birdsong and human language. Now, Miyagawa says, the researchers think that "the relationship is between birdsong and the expression system," with the lexical component of language having come from primates. Indeed, as the paper notes, the most recent common ancestor between birds and humans appears to have existed about 300 million years ago, so there would almost have to be an indirect connection via older primates -- even possibly the silvery gibbon.

As Berwick notes, researchers are still exploring how these two modes could have merged in humans, but the general concept of new functions developing from existing building blocks is a familiar one in evolution.

"You have these two pieces," Berwick says. "You put them together and something novel emerges. We can't go back with a time machine and see what happened, but we think that's the basic story we're seeing with language."

Miyagawa acknowledges that research and discussion in the field will continue, but says he hopes colleagues will engage with the integration hypothesis.

"It's worthy of being considered, and then potentially challenged," Miyagawa says.

It's the last bite that keeps you coming back for more

 

June 11, 2014

Association for Psychological Science

Your memory for that last bite of a steak or chocolate cake may be more influential than memory for the first bite in determining when you want to eat it again, according to research. The fact that memory for the last few bites seems to drive our decisions about when to eat a food again may be particularly relevant in places where portion sizes tend to be larger and are likely to result in lower end enjoyment:


Your memory for that last bite of a steak or chocolate cake may be more influential than memory for the first bite in determining when you want to eat it again, according to research published in Psychological Science, a journal of the Association for Psychological Science.

Our memories for foods are often vivid, especially when we experience foods that are terrifyingly bad or delightfully good. The findings from this research shed light on how memories for food are formed and how they guide our decisions about how soon we're willing to eat a food again.

"Research has told us a lot about factors that influence what foods people want to consume, but less is known about factors that influence when they want to consume a particular food again," explains researcher and lead author Emily Garbinsky of the Stanford University Graduate School of Business.

"Companies profit not only from the sale of food items but also from how frequently those particular items are sold, and the impact of eating both healthy and unhealthy foods on people's health is determined not only by how much they eat but how often those foods are eaten," says Garbinsky. "As such, it seemed important to get a better understanding of what influences the amount of time that passes until consumption is repeated."

Garbinsky and colleagues Carey Morewedge of the Boston University School of Management and Baba Shiv of the Stanford University Graduate School of Business investigated the question in a series of studies.

In one study, the researchers asked 134 undergraduate students to sample 3 flavors of Nut Thin crackers and then choose one to eat. They were then given a specific number of crackers and were asked to rate how much they enjoyed each one after they ate it.

The results revealed that students who had eaten the larger portion (15 crackers) reported significantly lower enjoyment at the end than those who had eaten the smaller portion (3 crackers).

These findings replicate previous findings on "sensory-specific satiety": Each bit of food is less pleasant than the one before it. Thus, the bigger the portion, the less enjoyment you get out of the last few bites.

More importantly, participants' enjoyment of the last cracker (manipulated by portion size) seemed to influence how soon the students wanted to eat the crackers again: Participants who ate a small portion typically opted to receive a giveaway box of Nut Thins sooner than did participants who ate the larger portion.

These results suggest that the most recent tastes experienced in the last few bites of a given food drive our decisions about when to eat that food again, a finding that they researchers replicated in a second study.

Garbinsky and colleagues hypothesized that this so-called "recency effect" might be explained by memory interference induced by the repetitiveness of eating:

"A glass of juice, bowl of ice cream, or bag of potato chips contains many units of very similar stimuli that are consumed one sip or bite at a time until the entire portion has been eaten," they write.

So, if we take a lot of bites of the same food in succession, our memory for the last bites may interfere with our ability to accurately remember the initial bites of that food.

Garbinsky and colleagues were able to eliminate this memory interference by reminding participants of their previous ratings as they continued to consume and rate a glass of juice. These participants were more accurate in remembering how much they enjoyed the first ounce of juice and they opted to receive a giveaway container of juice sooner than did the participants who rated each ounce of juice without being reminded of their previous ratings.

"This finding is important in that it suggests that large portions may be somewhat detrimental to companies because they extend the amount of time that passes until repeat consumption occurs," says Garbinsky. "And it's also important to the public, as eating too much of a favorite -- or healthy -- food may increase the delay until one wants to eat it again."

The studies do suggest that certain strategies -- such as thinking back to the first few bites -- could be used to encourage consumers to eat a food again soon. But, as tantalizing as these insights may be, Garbinsky cautions that more research is needed to investigate whether the findings translate to real-world settings, in which consumers have more control over deciding what and how much they eat.

Risk factors for hospital readmissions identified

 

June 11, 2014

Wake Forest Baptist Medical Center

According to researchers, about half of readmissions could be avoided. The goal of this single-center study was to identify at the time of discharge the factors that are strongly associated with readmission in patients with ischemic and hemorrhagic stroke. The study compared 79 stroke patients who were readmitted to the hospital within 30 days to 86 controls over an 18 month period.


Therefore, there is significant interest in identifying factors that influence readmission rates, especially those that can be identified prior to discharge. To pinpoint which stroke patients are most at risk, researchers at Wake Forest Baptist Medical Center undertook a retrospective case-control study to determine factors associated with readmission within 30 days. The study is published in the June 11 online edition of the American Journal of Medical Quality.

"If you can recognize who is at risk, you can really focus on those people to try to make sure they are treated appropriately and followed closely," said Cheryl Bushnell, M.D., associate professor of neurology at Wake Forest Baptist and director of its Comprehensive Stroke Center.

The goal of this single-center study was to identify at the time of discharge the factors that are strongly associated with readmission in patients with ischemic and hemorrhagic stroke. The study compared 79 stroke patients who were readmitted to the hospital within 30 days to 86 controls over an 18 month period. There were no significant differences in age, gender or race-ethnicity between the stroke patients and controls.

The researchers found that readmitted patients were significantly more likely to have a prior diagnosis of congestive heart failure, coronary artery disease, cancer or absence of hyperlipidemia, elevated lipid (fat) levels in the blood. In addition, readmitted patients were more likely to have been hospitalized two or more times during the year prior to the initial stroke admission.

The findings suggest that stroke severity and number of hospitalizations within the year prior to the stroke admission are important predictors of subsequent readmission within 30 days, independent of other clinical factors, Bushnell said.

"If our model is validated in a larger study, it could then be used in electronic health records to provide a potentially reproducible, efficient and effective means of selecting patients most at risk for subsequent hospital readmission. A logical next step is to develop innovative tools and programs for stroke patients to keep patients from being readmitted," Bushnell said.

A limitation of the study was that data was collected solely at discharge, she said, adding that subsequent research will include evaluation of post-discharge data.


Story Source:

The above story is based on materials provided by Wake Forest Baptist Medical Center. Note: Materials may be edited for content and length.


Journal Reference:

  1. Roy E. Strowd et al. Predictors of 30-Day Hospital Readmission Following Ischemic and Hemorrhagic Stroke. American Journal of Medical Quality, June 2014 DOI: 10.1177/1062860614535838

Pot Isn't Harmless, Top U.S. Health Official Says

 

WEDNESDAY June 4, 2014, 2014 -- States joining the march toward marijuana legalization need to take a step back and consider the drug's adverse effects on health, the U.S. drug "czar" argues in a new paper.

Marijuana is potentially addictive, proven to contribute to fatal motor-vehicle crashes, and can disrupt the brain function and learning of young users, says Dr. Nora Volkow, director of the U.S. National Institute on Drug Abuse.

Legalizing pot will lead to the sort of nationwide health problems now attributed to alcohol and tobacco, said Volkow, lead author of a review article in the June 5 New England Journal of Medicine.

Tobacco and alcohol have a far greater impact on health in the United States than illicit drugs, as their legal status make them more widely available for use, she noted.

"By making marijuana legal, you have more widespread use and many more health implications," Volkow said. "We don't need a third legal drug. We already have enough problems with the two we have."

The pro-marijuana advocacy group NORML agrees that pot "is not a harmless substance," Deputy Director Paul Armentano said.

"But its potential risks to the individual and to society do not warrant its present schedule I illicit status under federal law, a classification that improperly argues that the plant lacks any accepted therapeutic value and that its risks equal those of heroin," Armentano said.

Volkow is making her argument as the political winds continue to shift toward pot legalization.

Last week, the Republican-controlled U.S. House of Representatives voted in favor of preventing the federal government from interfering with states that allow marijuana use for medical reasons. Medical marijuana is legal in nearly half the states.

"Public opinion is shifting," Rep. Dana Rohrabacher, R-Calif., said at the time.

In the new article, Volkow and colleagues said marijuana is addictive, contrary to popular opinion. Research has shown that 9 percent of people who try pot will become addicted, she said. Pot's effect is even stronger among young people, addicting 17 percent of users under 18, she said.

"This is something that a lot of people who are pro-marijuana deny. The evidence shows otherwise," Volkow said.

Marijuana also poses a public safety risk. People intoxicated by pot are 3 to 7 times more likely to cause a car crash than someone sober, Volkow said.

Most troubling is the tendency for teens and young adults to use pot and alcohol at the same time, which increases the risk of a wreck more than if they used either drug on its own, she added.

Pot also appears to affect brain development in young users. Scans have shown that teenage pot users suffer from decreased brain activity and impaired connectivity between key brain areas, Volkow said.

"During adolescence, there is a tremendous amount of neuroplasticity," she said. "Regular use of marijuana is likely to have an adverse effect on the way the human brain gets connected and organized."

This may explain why frequent use by teens is linked to lower IQ and higher odds of dropping out of school, the report noted.

Volkow said other research has shown marijuana can:

  • Serve as a "gateway" drug.
  • Impair school performance.
  • Exacerbate mental illnesses such as schizophrenia.
  • Increase the risk of health problems such as chronic bronchitis and cardiovascular disease.

Legislators considering marijuana legalization should consider these effects, as well as all the gaps in current knowledge of pot's impact on human health, Volkow said.

"What is unfortunate in my view is that the information that's being presented is not objective. It's very subjective," she said. "We all want to think there is this drug that could make us feel relaxed and good with no harmful effects. That's a lovely fairy tale we all wish were true."

However, Armentano argues that "the ongoing criminalization of marijuana is a disproportionate response to what, at worst, is a health issue, not a criminal justice issue."

The adverse health consequences associated with alcohol, tobacco, and prescription drugs are far more dangerous and costlier to society than the responsible adult use of cannabis, he said. "It's precisely because of these consequences that these products are legally regulated and their use is restricted to particular consumers and specific settings," he said.

Legalization and regulation of marijuana will "best reduce the risks associated with the plant's consumption or abuse," Armentano said.

More information

For more information on marijuana, visit the U.S. National Library of Medicine.